Fast Cure Professional Use Adhesive PU Gun Foam for XPS, EPS, Concrete, Metal

• Customization: Available
• Bonding Function: Structural Adhesive
• Application: Construction
• Model NO.: JB960
• Classification: Room Curing
• Main Agent Composition: Polyurethane Elastomer
• Characteristic: Weatherability
• Promoter Composition: Coupling Agent
• Composition: Organic Material
• Color: White
• Mf: (C10h8n2o2.C6h14o3)X
• Shelf Life: 12 Months
• Component: One-Component
• Certificate: SGS Ios
• Name: High Performance PU Foam
• Type1: Manual
• Type2: Gun
• Goods: Class 2 Dangerous Good
• Useage: Construction, Home Decoration
• OEM: Yes
• Fire Resistant: Yes
• Formula1: Summer Formula
• Formula2: Winner Formula
• Transport Package: Can
• Specification: 750ml/can, 500ml/can; 12pcs/ctn
• Trademark: Junbond
• Origin: China
• HS Code: 3214109000
• Production Capacity: 50000pieces/Day

Product Description

Fast Cure Professional Use Adhesive Pu Gun Foam For Xps , Eps , Concrete, Metal

                               olyurethan Foa

JUNBOND 980 PU FOAM ADHESIVE  is a one-component, fast curing, easy to use adhesive foam ,special formula  designed for bonding XPS EPS Insulation Panels,wood and metal adhesive. Suitable to use at interior and exterior applications. Usable at high temperature like 45 °C and at low temperature like -5°C.

PRODUCT FEATURES   Polyurethan Foam adhesion

1. High Yield
2. Powerful Adhesion
3. Collapsing Gel Adhesive
4. Powerful adhesion of polystyrene heat panels (XPS and EPS).
5. Ready to mechanical fastening in two hours.
6. More economical.
7. Ready to use in aerosol can.
8. Up to 9m2 heat insulation panel adhesion for each can.
9. Minimum expansion during drying period.
10. After dried, no further expansion and shrinkage.
11. A lighter material compared to plaster which used in heat insulation systems.
12. No more extra burden or weight to building.
13. Depending on the humidity and temperature.
14. Application AreaBest for mounting heat insulation panels and filling voids during adhesive application.
15. Also advised for wooden type construction material bonding to concrete, metal etc.
16. Applications needed minimum expansion.
17. Mounting and isolation for frames of windows and doors.

 

APPLICATIONS AREAS   Polyurethan Foam adhesion

1. Best for mounting heat insulation panels and filling voids during adhesive application.
2. Also advised for wooden type construction material bonding to concrete, metal etc.
3. Applications needed minimum expansion.
4. Mounting and isolation for frames of windows and doors.

 

APPLICATION INSTRUCTIONS  Polyurethan Foam adhesion
1, Remove the dust, greasy dirt on the surface before construction.
2, Spray a little water on construction surface when the humidity is below 50 degrees, otherwise the heartburn or punch phenomenon will appear .
3, The flow rate of the foam can be adjusted by the control panel.
4, Shake the container for 1 minute before using, connect material container with spray gun or spray pipe, the filler content is 1/2 of the gap.
5, Use dedicated cleaning agent to clean the gun Surface drying time is about 5 minutes, and it can be cut after 30 minutes, after 1 hour the foam will be cured and achieve stable in 3-5 hours.
6, This product is not UV-proof, so it is suggested to be cut and coated after the foam curing (such as cement mortar, coatings,etc.)
7, Construction when temperature is lower than -10 ºC, to ensure the material can be exhausted and increase the foam expansion, it should be heated by 40 ºC to 50 ºC warm water

SAFETY RECOMMENDATION
1, Store the product in a dry, cool and atmospheric place with temperature under 45ºC.
2, The after-use container is forbidden to be burnt or punctured.
3, There should be atmospheric condition in construction site, the constructor should wear work gloves and goggles, don't be close to combustion source and don't smoke.
4, It is forbidden to invert or side lay in storage and transportation. (long inversion can cause valves blocking
5, This product contains micro harmful element, has certain stimulation to eyes, skin and respiratory system, In case the foam sticks to eyes, washing the eyes with clean water immediately or follow the doctor's advice, washing the skin with soap and clean water if touching the skin.